SpiderFix12 Complete Underfloor Heating Kits | 12mm Pipe
Upgrade your project with a SpiderFix12 low-profile UFH kit: 16.5mm panels, 12mm pipe, manifold and Grundfos UPM3 pump. For small-room retrofits.
Explore our systems
Upgrade your project with a SpiderFix12 low-profile UFH kit: 16.5mm panels, 12mm pipe, manifold and Grundfos UPM3 pump. For small-room retrofits.
Upgrade your project with a SpiderFix16 low-profile UFH kit: 20mm panels, 16mm pipe, manifold and Grundfos UPM3 pump. For small-room retrofits.
WATER UNDERFLOOR HEATING • COMPLETE SYSTEMS
Discover ThermRite SpiderFix underfloor heating kits for renovations, extensions and new-build projects. These complete water underfloor heating systems combine low-profile, self-adhesive pipe fixing panels with compatible heating pipe, a correctly sized manifold and a Grundfos UPM3 pump and temperature-control assembly.
Choose SpiderFix12 with 16.5mm panels for 12mm pipe, or SpiderFix16 with 20mm panels for 16mm pipe. Both systems securely retain the heating pipe ahead of application of a suitable self-levelling compound, helping create an accurate, low-profile heating installation.
The best system depends on your available floor height, room heat loss, heating circuit design and floor construction. Compare both SpiderFix variations below before selecting your kit.
| Feature | SpiderFix12 Kits | SpiderFix16 Kits |
|---|---|---|
| Panel thickness | 16.5mm | 20mm |
| Compatible UFH pipe | 12mm | 16mm |
| Panel dimensions | 1200 × 600mm | 1200 × 600mm |
| Panel installation | Self-adhesive, interlocking | Self-adhesive, interlocking |
| Pipe spacing | Flexible; design-dependent | Flexible; design-dependent |
| Typical application | Height-restricted retrofits and smaller circuits | Renovations, extensions and longer circuits where suitable |
Panel height is not the total finished floor build-up. Allow for levelling compound, any substrate preparation and the final floor covering.
Choose a 16.5mm or 20mm pipe fixing panel for suitable floor constructions where installation depth matters.
Self-adhesive backing, interlocking edges and integrated pipe grips simplify layout and installation.
Adapt pipe centres and circuit layouts to the heating design, heat source and individual room requirements.
Buy panels, pipe, manifold and pump components together, with quantities specified for each kit size.
ThermRite SpiderFix complete systems bring together the principal water underfloor heating components in one package:
Kit contents vary by size. Levelling compound, primer, insulation, floor finishes, thermostats and wiring controls are not included unless expressly stated on the product page. Browse our underfloor heating thermostats and controls separately.
SpiderFix is a wet-encapsulated pipe fixing system, rather than a dry overlay board. The appropriate preparation and levelling compound depend on the subfloor and finished floor specification.
STEP 01
Check that the substrate is clean, stable and suitable. Carry out required insulation, priming and floor preparation.
STEP 02
Fix and interlock the panels, install pipe at the designed spacing and connect the heating circuits to the manifold.
STEP 03
Pressure-test the circuits and apply an approved flexible fibre-reinforced levelling compound to the specified depth.
For product-specific instructions and installation documents, visit our underfloor heating boards and panels information centre.
NEED HELP CHOOSING?
Selecting between 12mm and 16mm pipe depends on more than floor height. Our team can help you assess the heated floor area, circuit design and suitable kit size. You can also explore SpiderFix panels or compare our complete underfloor heating systems.
Ask ThermRite for Advice
SpiderFix12 kits use 16.5mm-thick panels with 12mm underfloor heating pipe, while SpiderFix16 kits use 20mm-thick panels with 16mm pipe. Both feature self-adhesive backing, interlocking edges and flexible pipe spacing. Choose according to floor build-up, room heat loss and the heating circuit design.
Yes. Both SpiderFix systems are designed for use in suitable retrofit, renovation and new-build floor constructions. The low-profile panels are useful where available height is limited, although levelling compound and the finished floor covering must also be included in the total build-up.
Kit components include the specified SpiderFix panels, compatible underfloor heating pipe, a manifold, associated pipe connection components and a Grundfos UPM3 pump and temperature-control pack. Exact quantities and installation accessories depend on the kit size; always check the selected product listing.
Yes. The panels are designed to secure the pipe before encapsulation in a suitable flexible fibre-reinforced self-levelling compound. The compound type, preparation, minimum coverage and curing requirements must follow the manufacturers' instructions for the chosen subfloor and floor finish.
Yes, provided the full heating system is designed for the heat pump's operating temperatures and the room's heat-loss requirements. Pipe spacing, circuit lengths, flow rates and floor construction all affect heat output, so design requirements should be confirmed before installation.
FREE UNDERFLOOR HEATING QUOTATION
Upload your floor plans and receive a tailored underfloor heating quotation from our specialist team.